Register
Log In
Home
December 27, 2010
Offline
December 27, 2010
Offline
Hre is picture of 732 with barrel assembly came with 6 and 8 inch cost with shipping $378.00.Eric is making slapside stainless BA for it with wever rail.Gun still needs more cleaning up but I wanted to post pictures.Dthey make 4 inch BA for this gun?
Range Officer
Range Officers
Dans Club
March 27, 2009
Offline
Nice Dan you have there and Yes they make 4" and 2" for these. To bad it isn't blue as i have a couple BA's in 32m.
December 26, 2010
Offline
Really nice! Thanks for the 
. Is it a Palmer gun? I ask because as I started to clean and polish my Palmer 740 horrendous machine marks appeared on the frame. Basically from the trigger back, circular grinding marks appeared. On the right side there were so deep I could feel them with my finger nail. I mention this because the polishing became a much bigger job than I anticipated. On the plus side, now that I'm almost done it really shines. I'll try to start a thread with pics on it tonight.
Again, that is a really nice acquisition. Congrats!
December 27, 2010
Offline
Yes its a palmer gun ser number 000592 no machine marks all in all pretty nice gun once I cleaned up.If you use 320 wet& dry then go to 2500 then use mothers mag polish it works great on stainless.
Supporter
Moderators
Dans Club
February 22, 2009
Offline
Really nice snag, and I don't feel bad about missing that auction. One, because a DWF brother got it and two, it doesn't fit my Monson collection. Of course neither does the AGS...
Looking forward to hearing/ seeing how it shoots for you.
Best Regards,
Ron
Technically, the glass is always full; half liquid, half air....
May 17, 2010
Offline
Congrats.... I don't think I recall seeing any 732.. just the blue ones.
Wait Eric is making custom stuff over more shrouds.....
Get a rope. ( jk of course)
Soap Box, Ballot Box, Ammo Box
in that order.
4 Monson Model 15's
1 Palmer FB 15
1 Rossi 357 Model 92 (lever)
1 CZ 75B
December 26, 2010
Offline
waltfraz said:
Yes its a palmer gun ser number 000592 no machine marks all in all pretty nice gun once I cleaned up.If you use 320 wet& dry then go to 2500 then use mothers mag polish it works great on stainless.
Glad to hear it cleaned up well and is grind mark free. I started with the Mother's and discovered the grind marks. Being careful I tried the 2500 grit but that was very slow going. The 1000 grit was still slow but I could see progress so I haven't tried anything more aggressive. Then I went back to the 2500 and followed it with the Mother's. If I tilt the frame just right I can still see "waves" in the metal but it looks a lot better now, almost like it's been plated. I've got the cylinder left to do. Then it's clean and assemble. I need to get a good picture of the frame now that's it done and get the before and after pics posted.
Have you tried Renaissance Wax? I just got some but haven't tried it yet.
Supporter
Moderators
January 24, 2009
Offline
That is one killer
snag & the gun looks great! Congrats on landing that one.
February 20, 2008
Offline
Hey Walt - you Rock~!
Photo
If you're going to drink, don't drive. Don't even putt.
September 1, 2010
Offline
Very nice 732 you have there, congrats.
May 14, 2008
Offline
Very nice score. Price and cal.
Range Officer
Range Officers
Dans Club
February 9, 2009
Offline
Very cool 732 Walt. A real that can hardly be matched. Is it a Monson gun?
SMF
A man cannot have too many SuperMags
January 22, 2008
Offline
Great looking 732! It's very cool that it came with two barrel assemblies as well.
1 Guest(s)
