Log In
DWF Supporters
December 21, 2016
Offline
i've run across this situation on a .445. i know the 357 barrels won't work/fit on a 357 max frame. is the same true of the 44mag on a .445 frame? am i wrong? it's happened once before. LOL
DWF Supporters
Dans Club
Moderators
November 17, 2008
Offline
I will do my best.
Any small frame shroud will work on any small frame DW. Except Pork chops
Any large frame shroud will work on any large frame DW. Except a few have two alignment pins, this can be remedied.
Any super mag shroud will work on any large frame DW.ÂÂ
A large frame shroud will fit on a super mag but the ejector slot will be too short not allowing the cylinder to close and latch.
Odd barrel lengths and some compensated models may also be exceptions.ÂÂ
Anyone who sees an error in my conclusions please speak up.
ÂÂ
LB
Wisdom is merely the realization of how little one knows, therefore I am wise.
                                                              ÂÂ
DWF Supporters
December 21, 2016
Offline
thanks. i'm looking at a .445 on GB. i noticed it has a ported shroud marked .44 magnum. it appears to be o.k. but the shroud not matching the frame concerned me.
Supporter
Range Officer
Moderators
DWF Supporters
Dans Club
December 4, 2011
Offline
The ejector rod must have been replaced with a 44 mag or else the cyl won't close.  Either that or someone  milled out the slot to  accept the longer rod.
Anything worth doing is worth doing well.
My father
If a man designed it, and a man built it, then a man can fix it.
My grandfather
February 16, 2016
Offline
larry260 said
i'm looking at a .445 on GB. i noticed it has a ported shroud marked .44 magnum. it appears to be o.k. but the shroud not matching the frame concerned me. ÂÂ
I couldn't find it with my search ... can you throw up a link ?
DWF Supporters
December 21, 2016
Offline
its GB item 737810971. the frame has a 445 set #, but the shroud is marked .44 mag. the shroud is ported. i thought i read this shroud wouldn't work for the reasons you stated. plus i read SM barrels were heavier and wouldn't screw into a regular frame. so I thought a std barrel would be too small for a SM frame. too bad, as i'm trying to fins a 445 like and can afford. LOL. may be awhile. this one docent look "kosher".
Supporter
Dans Club
DWF Supporters
February 4, 2017
Offline
The answer simply takes a closer look...the seller hasn't got a clue. It's a 744 frame and shroud. Who knows where these folks pick up their model numbers?? 
I believe it says 44 S (as in 44 stainless).
"LIFE IS TOO SHORT TO SPEND IT WITH AN UGLY GUN!" - John Taffin
ÂÂ
ÂÂ
                                                                                  ÂÂ
February 16, 2016
Offline
larry260 said
the frame has a 445 set #
All the sellers information is correct and rimfire answered your question ... the S/N starts with 44S not 445.
DWF Supporters
December 21, 2016
Offline
thanks. i don't have my reading glasses on. LOL
Supporter
Dans Club
DWF Supporters
February 4, 2017
Offline
And I guess there's too much 60's residue floating around in me...caught the serial number but nor the model...SIGH.
"LIFE IS TOO SHORT TO SPEND IT WITH AN UGLY GUN!" - John Taffin
ÂÂ
ÂÂ
                                                                                  ÂÂ
DWF Supporters
December 21, 2016
Offline
i swear when i first looked at the listing, it said .445/.44. oh well. i'll be more careful.
Supporter
Dans Club
March 25, 2013
Online
I have recently corrected a seller who claimed a 744 was a 7445. Maybe it was corrected. 
. You can use a large frame ejector rod in a super mag though to solve the problem. I have a couple just in case I decide to do so. They just will not push cases all the way out.ÂÂ
1 Guest(s)
